- 您现在的位置：买卖IC网 > Sheet目录1214 > EVAL-ADM1021AEB (ON Semiconductor)BOARD EVAL FOR ADM1021
ADM1021A
Table 8. CONFIGURATION REGISTER BIT
ASSIGNMENTS
Bit Name Function
7 MASK1 0 = ALERT Enabled
1 = ALERT Masked
6 RUN/STOP 0 = Run
1 = Standby
Power-on
Default
0
0
and PCB track resistance. See Table 10 for an example of
offset values.
The offset value is stored as an 8-bit, twos complement
value. The value of the offset is negative if the MSB of
Register 0x11 is 1, and is positive if the MSB of
Register 0x11 is 0. This value is added to the remote
temperature. The offset register defaults to 0 at powerup.
The offset register range is ? 128 ? C to +127 ? C.
5 to 0
Reserved
0
Table 10. OFFSET VALUES
Conversion Rate Register
The lowest three bits of this register are used to program
the conversion rate by dividing the ADC clock by 1, 2, 4, 8,
Offset Register
Offset
(0x11) Value
Remote Temperature
(With (Without
Offset) Offset)
16, 32, 64, or 128 to give conversion times from 125 ms
(Code 0x07) to 16 seconds (Code 0x00). This register can be
written to and read back over the SMBus. The higher five
bits of this register are unused and must be set to 0. Use of
slower conversion times greatly reduces the device power
consumption, as shown in Table 9.
1111 1100
1111 1111
0000 0000
0000 0001
0000 0100
? 4 ? C
? 1 ? C
0 ? C
+1 ? C
+4 ? C
14 ? C
17 ? C
18 ? C
19 ? C
22 ? C
18 ? C
18 ? C
18 ? C
18 ? C
18 ? C
Table 9. CONVERSION RATE REGISTER CODE
Conversion/ Average Supply Current
Data Sec m A Typ at V CC = 3.3 V
0x00 0.0625 150
0x01 0.125 150
One-shot Register
The one - shot register is used to initiate a single conversion
and comparison cycle when the ADM1021A is in standby
mode, after which the device returns to standby. This is not
a data register as such, and it is the write operation that
causes the one - shot conversion. The data written to this
0x02
0x03
0x04
0x05
0x06
0x07
0x08 to 0xFF
0.25
0.5
1
2
4
8
Reserved
150
150
150
150
160
180
?
address is irrelevant and is not stored.
Serial Bus Interface
Control of the ADM1021A is carried out via the serial bus.
The ADM1021A is connected to this bus as a slave device,
under the control of a master device. Note that the SMBus
and SCL pins are three - stated when the ADM1021A is
powered down and will not pull down the SMBus.
Limit Registers
The ADM1021A has four limit registers to store local and
remote and high and low temperature limits. These registers
can be written to and read back over the SMBus. The high
limit registers perform a > comparison, while the low limit
registers perform a < comparison. For example, if the high
limit register is programmed as a limit of 80 ? C, measuring
81 ? C results in an alarm condition. Even though the
temperature measurement range is from 0 ? to 127 ? C, it is
possible to program the limit register with negative values.
This is for backwards compatibility with the ADM1021.
Offset Register
An offset register is provided at Address 0x11. This
allows the user to remove errors from the measured remote
Address Pins
In general, every SMBus device has a 7 - bit device address
(except for some devices that have extended 10 - bit
addresses). When the master device sends a device address
over the bus, the slave device with that address responds.
The ADM1021A has two address pins, ADD0 and ADD1,
to allow selection of the device address so that several
ADM1021A’s can be used on the same bus, and/or to avoid
conflict with other devices. Although only two address pins
are provided, these are three-state and can be grounded, left
unconnected, or tied to V DD so that a total of nine different
addresses are possible, as shown in Table 11.
It should be noted that the state of the address pins is only
sampled at powerup, so changing them after powerup has no
effect.
temperature. These errors can be introduced by clock noise
http://onsemi.com
10
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
EVAL-ADM1023EB
BOARD EVAL FOR ADM1023
EVAL-ADM1031EB
BOARD EVAL FOR ADM1031
EVAL-ADM1062TQEBZ
BOARD EVALUATION FOR ADM1062TQ
EVAL-ADM1075CEBZ
BOARD EVAL FOR ADM1075
EVAL-ADM1087EBZ
BOARD EVALUATION FOR ADM1087
EVAL-ADM1166TQEBZ
BOARD EVAL FOR ADM1166TQ
EVAL-ADM1168LQEBZ
BOARD EVAL FOR ADM1168LQ
EVAL-ADM1170EBZ
BOARD EVALUATION FOR ADM1170
相关代理商/技术参数
EVAL-ADM1022
制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board for Microprocessor System Temperature Monitor
EVAL-ADM1023
制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board for Microprocessor System Temperature Monitor
EVAL-ADM1023EB
功能描述:BOARD EVAL FOR ADM1023 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
EVAL-ADM1024EBZ
制造商:ON Semiconductor 功能描述:EVALUATION BOARD I.C. - Boxed Product (Development Kits)
EVAL-ADM1026EB
制造商:AD 制造商全称:Analog Devices 功能描述:Complete Thermal and System Management Controller
EVAL-ADM1028
制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board for PC Temperature Monitor and Fan Control ASIC
EVAL-ADM1030
制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board for ACPI Temperature Monitor and PWM Fan Controller
EVAL-ADM1031
制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board for ACPI Temperature Monitor and PWM Fan Controller